|
POLYTHERM®
POLYTHERM® is the best pre-insulated piping system we offer. It is a fiberglass jacketed, polyurethane foam insulated piping system for above and belowground distribution of liquids from -320°F to 250°F.
|
|
XTRU-THERM®
XTRU-THERM®, our "State of the Art" preinsulated piping system for fluids from cryogenic temperatures up to 250ºF. The extruded HDPE jacket results in a completely bonded system that moves as a single unit for maximum efficiency and service life.
|
|
ESCON-A®/ FERRO-SHIELD™
ESCON-A®/ FERRO-SHIELD™ is the original prefabricated, preinsulated piping system for the distribution of low to high pressure steam, high temperature hot water, and general fluid transportation systems.
|
|
MULTI-THERM® 500
MULTI-THERM® 500 is the best prefabricated, preinsulated piping system for the distribution of low to high pressure steam, high temperature hot water and general fluid transportation systems. The design eliminates corrosion and reduces energy loss.
|
|
UTILIDOR™
UTILIDOR™, is a rugged, prefabricated versatile tunnel for economically housing underground utility services. Utilidor can also be designed as a passage way between buildings
|
|
Prefabricated Manholes
PERMA-PIPE'S prefabricated steel manholes reduce installation and maintenance cost over traditional concrete manholes. They are fully assembled and tested with all internal pipe and valves as required.
|
|
TERRA-GARD™
TERRA-GARD™, is an economical choice for a preinsulated, prefabricated pipe and fitting system. The system is designed based on your system layout. The system consist of a carrier pipe, foam injected insulation and an outer jacket.
|
|
GALVA-GARD®
GALVA-GARD®, "The Ultimate Corrosion Fighter" is a prefabricated, preinsulated, fiberglass clad galvanized steel conduit system for low to high pressure steam, HTHW and general fluid transportation.
|
|
ULTRA-THERM®
ULTRA-THERM® is the next generation of prefabricated, preinsulated piping system for low to high pressure steam, HTHW and general fluid transportation is a fiberglass clad steel conduit system with no need for cathodic protection.
|
|
ECONO-GARD™
ECONO-GARD™ is a contractor friendly product, designed to be completed in the field. Straight sections of pipe are factory insulated and jacketed for delivery to the jobsite ready for field insulation and jacketing of joints and fittings.
|
|
PEX-GARD®
PEX-GARD® preinsulated pipe is designed for fast economical installation due to its long coil lengths and ability to be routed around obstructions. Bending PEX-GARD® eliminates the need for costly and time consuming welded elbows.
|
|
CHIL-GARD®
CHIL-GARD® is a cost effect factory preinsulated system for the underground chilled water and condenser water distribution. Gasketed bell joint construction accommodates pipe movement, eliminating expansion and contraction stresses wthin the system.
|
|
DUAL-GARD™ 250
DUAL-GARD™ 250 is a cost effective factory preinsulated system for the distribution of chilled water and hot water and condensate up to 250ºF.The system is provided with a FRP pipe inside a PVC outer jacket.
|
|
DUAL-GARD™ DI
DUAL-GARD™ DI is a cost effect factory preinsulated system for underground chilled water and low temperature hot water distribution. A ductile iron carrier pipe provides high corrosion resistance for underground applications.
|
|
COPPER-GARD™
COPPER-GARD™ is a completely factory-fabricated, preinsulated and jacketed copper piping system for hot and chilled water, condensate and domestic water distribution. It allows for quick installation of the underground distribution systems..
|
|
LO-TEMP - HI-GARD™
LO-TEMP - HI-GARD™, is a designed for the distribution of fluids aboveground at temperatures up to 250 ºF. Based on customers specifications, this is a prefabricated system with all fittings attached to straight sections.
|
|
MID-TEMP HI-GARD™
MID-TEMP HI-GARD™, is designed for distribution of fluids aboveground at temperatures of 250º F and higher. Based on customer specifications, this is a prefabricated system with all fittings attached to straight sections.
|
|
PAL-AT®
PAL-AT is a state of the art leak detection cable system that locates potential problems anywhere along the sensor string and alarms on contact.
|
|
DOUBLE-PIPE™Type-FS
DOUBLE-PIPE™Type FS is a prefabricated, secondary containment piping system for chemicals, process waste, fuel systems and general fluid transportation. Any carrier pipe type is permitted inside a FRP containment.
|
|
DOUBLE-PIPE™Type IW
DOUBLE-PIPE™Type IW is a stainless or alloy x stainless, alloy prefabricated, secondary containment piping system for hazardous chemicals, process waste and general fluid transportation. It is used where fluid is corrosive.
|
|
DOUBLE-PIPE™Type-HT
DOUBLE-PIPE™Type-HT is an economical choice for a prefabricated, preinsulated secondary containment piping system for high temperature or general fluid transportation. The system is carbon steel inside a carbon steel coated containment.
|
|
FLUIDWATCH®
FLUIDWATCH® is a system designed to monitor small areas for water or waterbased chemicals on floors and around sensitive equipment. Typical applications are for sub floors and around boilers and pumps.
|
|
LIQUIDWATCH®
LIQUIDWATCH® is a system designed to monitor sensor probes in a wide variety of applications for water, hydrocarbons or chemicals in sumps around sensitive equipment, tanks and low points in secondary contained pipe systems.
|
|
Infrared Leak Detection Survey
Infrared Leak Detection Survey is a economical non-evasive service that can locate areas of high thermal loss that are indicative of wet insulation due to conduit or service pipe leak.
|
|
Infrared Energy Evaluation Survey
Infrared Energy Evaluation Survey economical service to locate and quantifie BTU loss in underground pipe systems.
|
|
Sonic Leak Detection Survey
Sonic Leak Detection Survey is an economical non-evasive detailed survey to locate, pinpoint and classify leaks on buried water distribution systems both hot and cold fluids.
|
|
Tracer Gas Survey
Tracer Gas Survey is an economical choice for locating leaks in secondary containment and heat distribution conduit system in a non-evasive survey
|
|
Coating Discontinuity Test
Coating Discontinuity Test provides a non-evasive approach to coating integrity for all buried and coated piping systems.
|
|
Electronic Mapping
Electronic Mapping below grade pipe location is critical, our service provides detailed information on location and depth of metallic pipe.
|
|
Cathodic Protection Services
Cathodic Protection Services can provide complete system testing to insure that your CP system meets it's design life.
|
|
Skin Effect Current Tracing
Skin Effect Current Heat Tracing is the most cost effective heat tracing design for long runs of pipe. The design can be furinished as a single end power feed or mid fed power feed design on preinsulated pipe or field insualted pipe applications.
|
|
STEREO-HEAT® Impedence Heat Tracing
STEREO-HEAT® Impedance Heat Tracing is a direct current electric traced system across the ends of a steel or alloy pipeline section that provides even heat distribution on short to medium runs of preinsulated pipe.
|
|
Heat Tape Traced Systems
Heat Tape Traced Systems added to a preinsulated piping systems offers an economical and manitance free solution to any above or below grade fluid application that requires electric heat tracing.
|
|
|
Uniline Traced Piping Systems
Uniline® Traced Piping System is a muti-pipe bundled system that utilizes the heat from steam, hot water or electric heat tracing to provide the required operating temperature to heat fuel oil or chemicals in a economical design.
|
|
POLYTHERM® ULTRA LOW TEMPERATURE PIPING
POLYTHERM® Cryogenic Piping is a fiberglass jacketed, polyurethane foam insulated piping system for above and belowground distribution of liquids from -100ºF to -320ºF (-196ºC).
|
|
XTRU-THERM® ULTRA LOW TEMPERATURE PIPING
XTRU-THERM® Cryogenic piping is a high density polyethylene jacketed, polyurethane foam insulated piping system for above ground and below ground distribution of cryogenic liquids and gases from -100°F to -320°F(-196°C).
|
|
|
Ultrasonic Testing Survey
Ultrasonic Testing Survey can provide you peace of mind by measuring the remaining thickness of your alloy pipe systems.
|
|
AUTOTHERM®
AUTOTHERM®
|
|
|
PAL COM®
PAL COM®
|
|
ULTRA-FS™
ULTRA-FS™ is an advanced prefabricated, secondary containment piping system for chemicals, process waste, fuel systems and general fluid transportation is a fiberglass clad steel conduit system with no need for cathodic protection.
|
|
ULTRA-IW™
ULTRA-IW™ is an advanced prefabricated, secondary containment piping system for hazardous chemicals, process waste and general fluid transportation. It is a fiberglass clad stainless steel conduit system with no need for cathodic protection.
|
|
ULTRA-HT™
ULTRA-HT™ is an advanced preinsulated secondary containment piping system for general fluid transportation that requires an insulated steel containment. No need for cathodic protection.
|